Calculate how many pavers you need for a patio or walkway, including waste allowance. Use this paver patio calculator to work out exactly how many pavers, how much sand and how much base your patio needs.
Paver Patio Calculator
Free to use • No sign-up needed
Lay pavers on 4 inches of compacted crusher-run base plus 1 inch of screeded bedding sand. Sweep polymeric sand into the joints.
How to Use This Calculator
- Measure the length and width of the patio or walkway in feet.
- Enter the size of your pavers in inches.
- Choose a waste allowance for cuts and breakage.
- Click Calculate to see how many pavers you need.
What Is Paver Sand?
Paver sand is the fine sand used in two places in a paver project. First, as a thin bedding layer under the pavers, usually about 1 inch deep, screeded flat over the compacted gravel base. Second, as joint sand swept into the gaps between the pavers after they are laid.
The two jobs need different sand. Bedding sand is usually coarse concrete sand. It drains well and locks together under the pavers. Joint sand is finer, and it is often polymeric sand, which contains a binder that hardens when it gets wet and locks the pavers in place. Using the wrong sand in either spot causes problems: fine play sand washes out of joints, and soft sand under pavers shifts and lets them sink.
How Much Paver Sand Do I Need?
It depends on which layer you are filling.
- Bedding layer: About 1 inch deep over the whole paver area. One cubic yard covers about 300 square feet at 1 inch deep. A 10-by-10-foot patio needs about one-third of a cubic yard for bedding.
- Joint sand: A 50-pound bag covers roughly 100 to 200 square feet of pavers, depending on the paver size and the width of the gaps. Smaller pavers have more joints, so they need more sand. Wide gaps need more sand than tight ones.
Measure the paver area, not the whole yard. The calculator above works out both layers from your measurements, so you can order the right amount of each.
Polymeric Sand vs Regular Joint Sand
Polymeric sand is joint sand with a polymer binder mixed in. When you sweep it into the joints and wet it, the binder activates and the sand sets hard, almost like a flexible grout. Regular joint sand is just fine sand with no binder.
| Polymeric sand | Regular joint sand | |
|---|---|---|
| Locks pavers | Yes, sets hard | No, stays loose |
| Weed blocking | Good | Poor |
| Ant resistance | Good | Poor |
| Washes out in rain | Rarely | Often |
| Cost | Higher | Lower |
| Repairs | Harder to patch | Easy to top up |
Polymeric sand is the better choice for most patios and walkways because it keeps weeds and ants out of the joints and does not wash away in heavy rain. Regular sand is fine for a low-traffic path or a temporary job, and it is easier to repair. If you use polymeric sand, follow the bag instructions exactly. Too much water too fast washes the binder out before it sets, and too little water leaves it soft.
How to Apply Paver Sand
- Lay the pavers on the screeded bedding layer and tap them level.
- Spread joint sand over the pavers and sweep it into the gaps with a stiff broom.
- Run a plate compactor over the pavers with a rubber mat to settle the sand into the joints. Sweep in more sand and compact again.
- For polymeric sand, mist the joints lightly with water as the bag directs. Do not flood them.
- Let the joints dry fully before walking on the pavers or placing furniture.
Two common mistakes: skipping the compactor, which leaves joints half full, and watering polymeric sand like a garden, which washes the binder away. A light mist, a short wait, and a second light mist is the usual method.
How Deep Should the Bedding Layer Be?
The bedding layer is usually 1 inch deep after compaction. More than that lets pavers sink unevenly under weight. Less than that leaves high spots where the gravel base shows through.
Under the bedding layer, the gravel base should be 4 to 6 inches deep for a patio or walkway, and 6 to 8 inches for a driveway that carries cars. The base is compacted in layers before the sand goes down. The sand is not a substitute for a proper base. A thin base with a thick sand layer is the most common reason pavers settle and go wavy.
Common Mistakes to Avoid
- Using play sand or fill sand in the joints. It washes out in the first heavy rain.
- Making the bedding layer too thick. One inch is enough. More sand means more settling.
- Skipping compaction. Joints that are not compacted lose sand fast.
- Flooding polymeric sand. Mist it lightly, in two passes, as the bag directs.
- Forgetting the edge restraint. Without a solid edge, pavers spread outward and joints open up.
Bottom Line
Use coarse sand for the bedding layer and polymeric sand for the joints, keep the bedding layer to 1 inch over a proper gravel base, and compact the joints before watering. Use the calculator above to work out how much of each type you need before you order.
Written by the Yard & Bag Editorial Team. Our content is researched and checked against supplier guidance and standard building practice.
Related guides: How Much Sand Do I Need for Pavers?
Frequently Asked Questions
How much sand do I need for pavers?
There are two kinds of sand in a paver project. For the bedding layer, about 1 inch deep over the whole paver area, one cubic yard covers about 300 square feet. A 10-by-10-foot patio needs about one-third of a cubic yard for bedding. For joint sand, a 50-pound bag covers roughly 100 to 200 square feet of pavers, depending on the paver size and the width of the gaps.
What kind of sand do I use for pavers?
Use coarse concrete sand for the bedding layer under the pavers. It drains well and locks together. Use polymeric sand for the joints between the pavers, because it hardens when it gets wet and locks the pavers in place. Do not use play sand or fine masonry sand: play sand washes out of joints, and soft sand under pavers shifts and lets them sink.
Polymeric sand vs regular joint sand?
Polymeric sand is joint sand with a polymer binder mixed in. When you sweep it into the joints and wet it, the binder activates and the sand sets hard, almost like a flexible grout. It keeps weeds and ants out of the joints and does not wash away in heavy rain. Regular joint sand is just fine sand with no binder. It costs less and is easier to repair, so it is fine for a low-traffic path or a temporary job. If you use polymeric sand, follow the bag instructions exactly: too much water too fast washes the binder out, and too little water leaves it soft.
How deep should sand be under pavers?
One inch of screeded bedding sand after compaction, over a 4- to 6-inch compacted gravel base for a patio or walkway, and 6 to 8 inches for a driveway. More than 1 inch of sand lets pavers sink unevenly under weight. The sand is only a leveling layer, not a substitute for a proper base.
How do I apply joint sand?
Spread joint sand over the pavers and sweep it into the gaps with a stiff broom. Run a plate compactor over the pavers with a rubber mat to settle the sand, then sweep in more sand and compact again. For polymeric sand, mist the joints lightly with water as the bag directs and do not flood them. Let the joints dry fully before walking on the pavers or placing furniture.