Estimate the concrete needed for footings and piers, by length, width and depth. Use this concrete footing calculator to work out exactly how much concrete your footings need before you order.
Concrete Footing Calculator
Free to use • No sign-up needed
Footings must sit below the frost line in cold climates — check your local code. Round footings are typical for deck posts.
How to Use This Calculator
- Measure the length and width of the footing in feet.
- Enter the depth of the footing in inches.
- Enter how many footings you need, if asked.
- Click Calculate to see how much concrete you need in cubic yards and bags.
What Is a Concrete Footing?
A footing is the wide concrete base at the bottom of a foundation. It spreads the weight of the building over a larger area of soil, so the walls do not sink or crack. Every house, deck, retaining wall and large shed sits on footings of some kind.
Footings are usually the first concrete poured on a building project, and they set the level for everything above them. A footing that is out of level or in the wrong place causes problems for the whole build, so it is worth taking the time to get them right.
Types of Concrete Footings
- Strip footings: Long, continuous strips of concrete under foundation walls. The most common type for houses and garages.
- Pad footings: Square or round pads under individual posts or columns, such as deck posts or porch columns.
- Pier footings: Deep, narrow footings, often formed with tubes, that reach down to solid ground or below the frost line. Used for decks and light structures.
- Thickened-edge slab: A concrete slab with a deeper edge where the walls sit. The edge acts as the footing, so no separate footing is poured.
The type depends on the structure, the soil and the local building code. A deck usually needs pier or pad footings. A house usually needs strip footings.
How Deep and How Wide Should a Footing Be?
Two rules decide footing size: it must sit below the frost line, and it must be wide enough to spread the load.
- Depth: The bottom of the footing must be below the local frost line. In the far south that can be 12 inches or less. Through the middle of the country it is usually 18 to 36 inches. In the northern states it can be 48 inches or more. Check your local building code for the exact depth.
- Width: A common rule is to make the footing twice as wide as the wall it supports. A typical 8-inch foundation wall sits on a 16-inch-wide footing. A residential strip footing is often 12 to 24 inches wide and 8 to 12 inches thick.
- Thickness: 8 to 12 inches is normal for a house footing. Heavier buildings need thicker footings.
These are typical sizes, not engineering. For a large or two-story building, or for poor soil, a structural engineer or your local building department should confirm the size.
How Much Concrete Do I Need for Footings?
The volume is simple: length times width times depth, in feet, divided by 27 to get cubic yards. The calculator above does the math for strip, pad and pier footings.
As a quick example, a strip footing 40 feet long, 16 inches wide and 12 inches deep needs about 1.8 cubic yards. A pad footing 2 feet square and 12 inches deep needs about 0.15 cubic yards, so a set of ten pads needs about 1.5 cubic yards. Always order 5 to 10 percent extra. Running short in the middle of a footing pour is far worse than having a little left over.
For small pad footings, bagged mix works. An 80-pound bag yields about 0.6 cubic feet, so one cubic yard takes about 45 bags. For strip footings, ready-mix delivered by truck is almost always cheaper and easier.
Rebar in Footings: Do You Need It?
Most house footings need steel reinforcement, called rebar. Two continuous bars of #4 rebar (half an inch thick) running the length of a strip footing is the usual minimum, held up on chairs so the steel sits in the middle of the concrete, not on the ground.
Rebar stops the footing from cracking when the ground moves or the load shifts. Some small pad footings for decks do not need it, but strip footings under walls almost always do. Your local building code will say what is required, and many towns require a footing inspection before the concrete is poured, so the inspector can check the rebar and the depth.
Pouring Footings: Tips That Matter
- Dig to undisturbed soil. Never pour a footing on loose fill or topsoil. It compresses and the footing sinks.
- Keep the trench dry. Water in the trench weakens the concrete and washes the cement out of the mix.
- Set anchor bolts while the concrete is wet if a sill plate will sit on the footing. It is far harder to add them later.
- Level the top. A footing that is out of level by an inch makes every course of block or framing above it harder.
- Cure it properly. Keep the concrete moist for several days and do not load it until it has had time to gain strength, usually at least 7 days for light loads.
Common Mistakes to Avoid
- Pouring above the frost line. Frost heave lifts the footing and cracks the wall above it.
- Pouring on disturbed or loose soil. The footing settles unevenly.
- Skipping rebar where the code requires it.
- No inspection. Many jurisdictions require the footing to be inspected before the pour. Pouring without it can mean digging it out.
- Ordering exactly the calculated amount. Always add 5 to 10 percent.
Bottom Line
Dig below the frost line, make the footing twice as wide as the wall, use rebar, pour on solid ground, and order a little extra concrete. Use the calculator above to work out how many cubic yards and bags you need before you order.
Written by the Yard & Bag Editorial Team. Our content is researched and checked against supplier guidance and standard building practice.
Related guides: How Much Concrete Do I Need for a 10×10 Slab?
Frequently Asked Questions
How much concrete do I need for footings?
Multiply the length, width and depth in feet, then divide by 27 to get cubic yards. A strip footing 40 feet long, 16 inches wide and 12 inches deep needs about 1.8 cubic yards. A pad footing 2 feet square and 12 inches deep needs about 0.15 cubic yards, so a set of ten pads needs about 1.5 cubic yards. Always order 5 to 10 percent extra.
How deep should footings be?
The bottom of the footing must sit below the local frost line. In the far south that can be 12 inches or less. Through the middle of the country it is usually 18 to 36 inches. In the northern states it can be 48 inches or more. Check your local building code for the exact depth.
How wide should a footing be?
A common rule is to make the footing twice as wide as the wall it supports. A typical 8-inch foundation wall sits on a 16-inch-wide footing. A residential strip footing is often 12 to 24 inches wide and 8 to 12 inches thick.
Do footings need rebar?
Strip footings under walls almost always do. Two continuous bars of #4 rebar running the length of the footing is the usual minimum, held up on chairs so the steel sits in the middle of the concrete. Some small pad footings for decks do not need it. Your local building code will say what is required, and many towns require a footing inspection before the concrete is poured.
Should I use bags or ready-mix for footings?
For small pad footings, bagged mix works. An 80-pound bag yields about 0.6 cubic feet, so one cubic yard takes about 45 bags. For strip footings, ready-mix delivered by truck is almost always cheaper and easier than mixing that many bags.