How much sand do I need for pavers — sand base between concrete pavers

How Much Sand Do I Need for Pavers?

How much sand do I need for pavers? Pavers need sand in two places: a bedding layer underneath them, and joint sand swept into the gaps between them. The two sands are different, and the amounts work out differently too. As a quick answer, a 10-by-10-foot patio needs about one-third of a cubic yard of bedding sand and about one 50-pound bag of joint sand. Our free Paver Patio Calculator works out both amounts for your patio, and this guide explains the depth, the sand types and the cost behind it. Use our paver sand calculator to work out exactly how much sand your patio needs.

How Much Sand Do I Need for Pavers? (Bedding Layer)

Bedding sand is the 1-inch layer of coarse sand that pavers sit on. It levels the base and lets you set each paver flat. One cubic yard of bedding sand covers about 324 square feet at 1 inch deep. Our paver sand calculator uses the same 1-inch depth to work out the cubic yards.

  • 10 x 10 feet (100 sq ft): about 0.3 cubic yards, about 9 bags (50-pound bags)
  • 10 x 20 feet (200 sq ft): about 0.6 cubic yards, about 17 bags
  • 12 x 12 feet (144 sq ft): about 0.45 cubic yards, about 12 bags
  • 20 x 20 feet (400 sq ft): about 1.25 cubic yards, about 34 bags

Always add 5 to 10 percent extra for uneven ground and waste. The bedding layer should be exactly 1 inch deep after screeding. Thicker than that, and the pavers settle unevenly underfoot. Thinner, and the pavers rock.

To work out the bedding sand for your patio, use our Paver Patio Calculator. It asks for the patio size and the sand depth, and gives you cubic yards and bags. If you are also working out the base stone underneath, see our Paver Base Calculator.

How Much Joint Sand Do I Need?

Joint sand fills the narrow gaps between pavers and locks them together. The amount depends on the paver size and the joint width. As a rule of thumb, one 50-pound bag of joint sand covers roughly 50 to 100 square feet of pavers with standard narrow joints.

  • 100 sq ft patio: about 1 to 2 bags (50-pound bags)
  • 200 sq ft patio: about 2 to 4 bags
  • 400 sq ft patio: about 4 to 8 bags

Wider joints and smaller pavers need more sand, because there is more joint area per square foot. If your joints are wider than about 1/4 inch, order extra. It is better to have one bag left over than to run short with half the joints unfilled. Our paver sand calculator covers joint sand too — enter the patio size and it adds the joint bags to the bedding total. How much sand do I need for pavers with wide joints? Order an extra bag or two beyond the table above.

What Type of Sand for Pavers?

There are three sands involved in a paver job, and each has its own place.

  • Bedding sand: Coarse concrete sand, sometimes called sharp sand or C33 sand. Angular grains lock together and do not wash away easily. This is the 1-inch layer under the pavers.
  • Joint sand: Fine sand swept into the gaps. Polymeric sand is the modern choice. It has a binding agent that hardens when wet, so it stays in the joints and blocks weeds and ants.
  • Polymeric sand vs regular sand: Regular joint sand is cheaper, but it washes out in heavy rain and weeds grow through it. Polymeric sand costs more, usually $20 to $40 per 50-pound bag, but it sets hard, resists washout and keeps weeds down for years. For a patio you plan to keep, polymeric sand is worth the extra cost.

Do not use play sand or mason sand for bedding. Play sand is too fine and rounded, so it shifts underfoot. Mason sand is fine for joints but too soft for bedding. Use coarse concrete sand for the bedding layer. If you are unsure how much of each sand to buy, our paver sand calculator splits the bedding and joint amounts for your patio size. How much sand do I need for pavers if I use polymeric sand? The same amount by volume — the bag price is what changes.

How Much Does Paver Sand Cost?

Bedding sand usually runs about $30 to $60 per cubic yard in bulk, or $4 to $7 per 50-pound bag. For a 10-by-20-foot patio, the bedding sand costs roughly $20 to $40 in bulk, or about $70 to $120 in bags. Bulk is far cheaper once you pass about half a cubic yard.

Polymeric joint sand usually runs $20 to $40 per 50-pound bag. A 200-square-foot patio needs 2 to 4 bags, so roughly $40 to $160 for the joints. Prices vary by region and brand, so get two or three quotes before you order. Run the numbers through our paver sand calculator first, so you know the cubic yards and bag counts before you compare prices. So how much sand do I need for pavers altogether? Bedding plus joints, with 5 to 10 percent extra for waste.

Steps to Sand a Paver Patio

  1. Lay and compact the base stone, then screed the bedding sand to exactly 1 inch deep.
  2. Lay the pavers on the screeded sand, keeping the joints even.
  3. Sweep dry joint sand over the pavers, working it into every gap.
  4. Run a plate compactor over the pavers with a protective pad, then sweep more sand into the joints.
  5. If you are using polymeric sand, mist the patio lightly with water so the binder sets. Do not flood it.
  6. Let the sand set for 24 hours before heavy use.

If you are still planning the patio, our Sand Estimator works out sand for any area, and our Paver Patio Calculator covers pavers, sand and base together. The Concrete Masonry & Hardscapes Association publishes installation guidance for interlocking concrete pavers, including bedding and joint sand.

Common Mistakes to Avoid

  • Bedding sand too thick. More than 1 inch lets pavers settle and rock.
  • Using play sand for bedding. It is too fine and rounded, and the pavers shift.
  • Skipping joint sand. Without it, pavers move, weeds grow through, and ants nest in the gaps.
  • Flooding polymeric sand. Too much water washes the binder out before it sets. Mist it lightly.
  • Ordering exactly the calculated amount. Always add 5 to 10 percent for waste and uneven ground.

Bottom Line

Use 1 inch of coarse concrete sand under the pavers and polymeric sand in the joints. A 10-by-10-foot patio needs about one-third of a cubic yard of bedding sand and about one bag of joint sand. Use our free Paver Patio Calculator to work out the exact amounts for your patio before you order. For a 20-by-20-foot patio, how much sand do I need for pavers? About 1.25 cubic yards of bedding sand and 4 to 8 bags of joint sand.

Written by the Yard & Bag Editorial Team. Our content is researched and checked against supplier guidance and standard building practice.

Scroll to Top