How much gravel do I need

How Much Gravel Do I Need?

How much gravel do I need? A 10-by-10-foot area at 3 inches deep needs about 0.93 cubic yards — roughly 1.3 tons. The exact amount is just length × width × depth, and our free gravel calculator does the math for any project size, in cubic yards, tons and bags.

The Short Answer: The Gravel Formula

Cubic yards = length (feet) × width (feet) × depth (inches) ÷ 324. Then tons = cubic yards × 1.4 for general gravel. That is all there is to it — the 324 folds the two conversions (inches to feet, cubic feet to cubic yards) into one step. Worked example: a 10 × 10 foot patio at 3 inches deep is 10 × 10 × 3 ÷ 324 = 0.93 cubic yards. Multiply by 1.4 and you get about 1.3 tons. Our gravel calculator runs the same formula and adds the 10% extra for compaction and spillage, so you can skip the arithmetic entirely.

How Deep Should Gravel Be?

Depth is set by what the gravel has to carry. A decorative path needs far less stone than a driveway that carries cars.

Project Depth Best stone
Garden paths, decorative beds 2–3 in pea gravel
Walkways 3 in pea gravel or crushed stone
Patio or paver base 4–6 in compacted, plus ~1 in of sand crusher run / crushed stone
Driveway top-up 2–4 in on top crushed stone #57
New driveway, light vehicles 4–6 in crusher run base + #57 surface
New driveway, heavy vehicles or soft ground 8–12 in total, in layers large base stone, then #57

One honest note: no university extension service publishes a standard gravel depth table — the figures above come from supplier and installer guidance, not a lab. The closest authority source is Oregon State University Extension’s 10-Step Guide to Installing Pavers, which puts a crushed-rock base at 4 to 6 inches for patios and says to make it thicker where the surface will be driven on. For driveways, build in layers and compact each one — a 4-inch base goes down as two 2-inch compacted lifts, not one pour. If your project is a driveway specifically, our guide to how much gravel you need for a driveway covers the layered build in detail.

How Much Gravel Do I Need for a 10×10 Area?

The table below covers the most common project sizes at typical depths. Find your project, read across, and add about 10% when you order.

Project Size & depth Cubic yards Tons
Garden path 25 × 3 ft @ 2 in 0.46 0.7
Patio 10 × 10 ft @ 3 in 0.93 1.3
Patio / paver base 10 × 10 ft @ 4 in 1.23 1.7
Shed base 12 × 12 ft @ 4 in 1.78 2.5
Driveway 10 × 20 ft @ 4 in 2.47 3.5
Driveway 20 × 12 ft @ 4 in 2.96 4.1
Driveway 30 × 12 ft @ 4 in 4.44 6.2

How much gravel do I need for a 10×10 area at 4 inches instead of 3? About a third more — 1.23 cubic yards instead of 0.93. Depth is the input that moves the order most: doubling the depth doubles the material, so measure the job before you choose it.

Cubic Yards to Tons: How Much Does Gravel Weigh?

Suppliers sell by the cubic yard or by the ton, and the quote you get often uses whichever one they prefer — so convert before you compare prices.

Material Pounds per cubic yard Tons per cubic yard
General gravel 2,800 1.4
Crushed stone 2,800 1.4
Pea gravel 2,700 1.35
Crusher run / dense grade 3,000 1.5

One ton of general gravel is about 0.71 cubic yards. One cubic yard covers about 162 square feet at 2 inches deep, 108 square feet at 3 inches, and 81 square feet at 4 inches. Wet material weighs noticeably more than dry, and stone size and moisture shift the numbers by 5 to 10 percent — when a supplier gives you their own density figure, use it. We cover the weight question in full in our guide to how much a cubic yard of gravel weighs.

Bags or Bulk?

One cubic yard equals 27 cubic feet, and a standard 0.5-cubic-foot bag holds half a cubic foot — so one cubic yard takes 54 bags. The 10 × 10 foot patio at 3 inches deep (0.93 cubic yards, 25 cubic feet) needs about 50 bags. Bags make sense for a small path, a top-up, or a job with no truck access. Above about 1 cubic yard, bulk delivery is far cheaper per cubic yard, and you skip carrying fifty bags one by one.

Order 10% Extra

Gravel settles and compacts, and you lose a little to spillage and uneven ground — so once you know how much gravel do I need, add about 10% to the formula result. Crushed stone compacts to about 85% of its loose volume, so a load that looks right on delivery ends up low once it is raked and driven on. A second delivery costs far more than the extra half-yard in the first one.

Which Gravel for Which Job

Not all gravel is interchangeable — using the wrong type leads to ruts, drainage problems, or a surface that never firms up.

  • Crushed stone #57 (angular, about 3/4 inch): driveways and drainage. The angular edges lock together under weight and will not shift.
  • Crusher run / #411 (mixed stone and fines): base layers. It packs down hard and makes the firmest foundation.
  • Pea gravel (rounded, about 3/8 inch): paths and decorative beds. It does not compact, so it ruts under cars — never use it for a driveway.
  • River rock: decorative beds and borders only. It is too large and too smooth to walk or drive on comfortably.

Bottom Line

So how much gravel do I need? Measure the length and width, pick the depth for the job, and divide by 324 for cubic yards — then multiply by 1.4 for tons and add 10%. For the common 10 × 10 foot patio at 3 inches deep, that is 0.93 cubic yards, about 1.3 tons, or roughly 50 bags. Use our free gravel calculator to work out the exact cubic yards, tons and bags for your project before you order.

Frequently Asked Questions

How much gravel do I need for a 10×10 area?

About 0.93 cubic yards (1.3 tons) at 3 inches deep, or 1.23 cubic yards (1.7 tons) at 4 inches deep. Add 10% for compaction and spillage.

How many tons of gravel do I need?

Multiply cubic yards by about 1.4 for general gravel. A 10 × 20 foot driveway at 4 inches deep is 2.47 cubic yards, about 3.5 tons. A 30 × 12 foot driveway at the same depth is 4.44 cubic yards, about 6.2 tons.

How deep should gravel be for a driveway?

Four to 6 inches for light vehicles, 8 to 12 inches in compacted layers for heavy vehicles or soft ground. Topping up an existing driveway takes 2 to 4 inches of fresh stone. Always excavate 1 to 2 inches deeper than the finished depth to allow for compaction.

How much does a cubic yard of gravel weigh?

About 2,800 pounds (1.4 tons) for general gravel and crushed stone. Pea gravel is about 2,700 pounds per cubic yard, and crusher run is about 3,000 pounds. Wet stone weighs more than dry.

How much gravel do I need for a garden path?

A 25 × 3 foot path at 2 inches deep needs about 0.46 cubic yards — roughly 0.7 tons, or about 25 half-cubic-foot bags. Use pea gravel for paths; it is comfortable to walk on and easy to rake level.

Written by the Yard & Bag Editorial Team. Our content is researched and checked against supplier guidance and standard building practice.

Scroll to Top